Stelpro Electric Baseboard Heaters Whitby, Ontario
Stelpro Brava In Stock at MarsLED
Whitby, Ontario • Electric Heating
Stelpro Electric Baseboard Heaters in Whitby
Shop stocked Stelpro Brava electric baseboard heaters for Whitby homes, rental properties, additional dwelling units, basement renovations, contractor projects and property-management applications. MarsLED carries 120 V and 240/208 V Brava models plus compatible built-in thermostat options.
Stelpro Brava Whitby
Electric baseboard heating for Whitby homes and projects.
Electric baseboard heating can be a practical option in Whitby homes, rental units, additional dwelling units and renovation projects where the electrical and heating design calls for electric resistance heat. Stelpro Brava heaters provide multiple wattage and voltage configurations for project-specific selection.
Stelpro identifies Brava for bedrooms, dining rooms, living rooms and offices. Its rounded corners, one-piece rugged casing and installer-friendly design also make the platform useful for replacement work and ongoing property maintenance.
Why Brava?
Brava combines low-profile electric convection heat with the durability and clean appearance needed for residential and appropriate light-commercial environments.
- Rounded-corner design
- Rugged one-piece steel casing
- Quiet heating-element design
- Multiple wattage and voltage options
- Optional built-in thermostat control
Whitby property-standards context
Whitby defines adequate and suitable heat as a minimum 20°C within a dwelling unit.
Whitby's current Property Standards By-law defines adequate and suitable heat as a minimum air temperature of 20°C within a dwelling unit. Heating and related building systems must be maintained to the applicable property-standards requirements.
For electrically heated homes, rentals and additional dwelling units, properly specified permanent baseboard heaters can support replacement and renovation work when the heater voltage, wattage, circuit capacity, clearances and calculated heating requirements are confirmed for the project.
Stocked at MarsLED
Compare Stelpro Brava baseboard heaters.
Choose from the stocked MarsLED Brava range below. Heater selection should be based on the project's calculated heating load, voltage, circuit requirements, dimensions, clearances and applicable electrical requirements—not wattage or room size alone.
| Model | Power | Voltage | Length | Shop |
|---|---|---|---|---|
| B0501W | 500 W | 120 V | 27-7/8" | View B0501W |
| B0751W | 750 W | 120 V | 37-5/8" | View B0751W |
| B1001W | 1000 W | 120 V | 47-1/2" | View B1001W |
| B0502W | 500 / 375 W | 240 / 208 V | 27-7/8" | View B0502W |
| B0752W | 750 / 560 W | 240 / 208 V | 37-5/8" | View B0752W |
| B1002W | 1000 / 750 W | 240 / 208 V | 47-1/2" | View B1002W |
| B1502W | 1500 / 1125 W | 240 / 208 V | 66-1/4" | View B1502W |
| B2002W | 2000 / 1500 W | 240 / 208 V | 83-7/8" | View B2002W |
Electrical selection
120 V or 240/208 V? Match the heater to the project.
Voltage must match the electrical design and circuit serving the heater. When replacing an existing baseboard or planning a new installation, confirm voltage, wattage, circuit capacity and installation conditions before ordering.
B0501W • B0751W • B1001W
MarsLED stocks three 120 V Brava models from 500 W through 1000 W for projects designed around 120 V electric baseboard heating.
500 W through 2000 W
The stocked 240/208 V Brava range includes five models. Output is lower at 208 V, so both ratings are shown on the individual product pages.
Whitby application guide
Where Brava fits into Whitby projects.
Brava heaters can support a wide range of projects when electric resistance baseboard heat is appropriate for the building and the heater is correctly specified.
Replacement or new electric heating in bedrooms, living areas, offices, basements and additions.
Heating for permitted principal-residence, basement or detached-accessory-building ADU projects where electric baseboard heat is part of the approved electrical and heating design.
Replacement and maintenance work in electrically heated rented residential units.
Stocked heater options for ongoing building maintenance, renovation and replacement programs.
Multiple wattage and voltage options for properly specified installation and retrofit work.
A familiar electric-heating platform for renovation, addition and residential construction projects.
Additional dwelling units in Whitby
Whitby's housing program has increased permissions to four residential units as-of-right per lot.
Whitby uses the term Additional Dwelling Unit (ADU). The Town describes an ADU as a self-contained dwelling unit that is accessory and secondary to the principal residential dwelling. ADUs may be located within the principal residence or within an accessory building on the same lot.
Whitby's Housing Accelerator Fund program reports that its Legal Additional Dwelling Unit initiative increased permissions from three to four residential units as-of-right per lot. Property-specific zoning, servicing, environmental and other restrictions can still apply.
The Town's zoning provisions state that no more than one ADU may be located within an accessory structure. They also include special restrictions for lands outside the urban boundary, Oak Ridges Moraine areas, Greenbelt lands, Environmental Protection, Natural Heritage System and hazard lands.
A building permit is required for both principal-residence and detached ADUs. Whitby's permit guidance identifies architectural and other technical documentation that may be required, including HVAC drawings/documents. If electric baseboard heating forms part of the approved design, confirm heating load, voltage, wattage, circuit capacity and clearances before ordering.
Whitby ADU considerations
- Confirm zoning and servicing eligibility for the property
- Confirm the proposed project stays within current unit permissions
- No more than one ADU may be located in an accessory structure
- Check environmental, Greenbelt, Oak Ridges Moraine and hazard-land restrictions where applicable
- Obtain the required building permit before construction
- Match heater voltage and wattage to the approved electrical and heating design
Built-in temperature control
Complete the Brava installation with a Stelpro thermostat.
MarsLED stocks both built-in mechanical thermostat options. Compatibility and the correct control type should be confirmed for the specific heater and project before installation.
Single-Pole Built-In Thermostat
Mechanical 120–600 V built-in temperature control for compatible Stelpro baseboard heater installations.
View SIBT1WDouble-Pole Built-In Thermostat
Mechanical 120–600 V double-pole built-in thermostat for compatible Stelpro baseboard heater installations.
View SIBT2WWhitby product questions
Stelpro baseboard heater FAQ — Whitby
Where can I buy Stelpro Brava baseboard heaters for a Whitby project?
MarsLED stocks multiple Stelpro Brava 120 V and 240/208 V electric baseboard heaters for Whitby homeowners, contractors, electricians, landlords and property-management customers.
What does Whitby define as adequate and suitable heat?
Whitby's current Property Standards By-law defines adequate and suitable heat as a minimum air temperature of 20°C within a dwelling unit.
What terminology does Whitby use for secondary residential units?
Whitby uses the term Additional Dwelling Unit, or ADU.
How many residential units does Whitby's current housing program permit as-of-right per lot?
Whitby's Housing Accelerator Fund program states that the Legal Additional Dwelling Unit initiative increased permissions from three to four residential units as-of-right per lot, subject to applicable property-specific restrictions.
Can a Whitby ADU be located inside the principal residence?
Yes. Whitby accepts building-permit applications for ADUs located within qualifying principal residences.
Can a Whitby ADU be located in a detached accessory building?
Yes. Whitby permits qualifying detached ADUs, although no more than one ADU may be located within an accessory structure and zoning requirements apply.
Are Whitby's ADU permissions identical on every property?
No. Servicing, environmental, hazard-land, Greenbelt, Oak Ridges Moraine and other zoning provisions can change what is permitted on a specific property.
Does a Whitby ADU require a building permit?
Yes. The Town lists both principal-residence and detached Additional Dwelling Units among projects requiring building permits.
Can HVAC documentation be required for a Whitby building permit?
Yes. Whitby's building-permit guidance lists HVAC drawings and documents among technical materials that may apply to a project.
Can I replace an old baseboard heater with a Brava model of the same wattage?
Not automatically. Confirm voltage, circuit requirements, calculated heating load, dimensions, clearances and installation requirements before choosing a replacement.
Should I buy a 120 V or 240 V baseboard heater?
The heater voltage must match the electrical design of the project. Confirm the existing circuit or project requirements before ordering.
Does MarsLED supply Stelpro heaters for contractor and property-management projects in Whitby?
Yes. MarsLED's stocked Brava portfolio is available for residential, renovation, rental-property, contractor and property-management projects in Whitby and Durham Region, subject to product availability.
Can a built-in thermostat be added to a Stelpro Brava heater?
Compatible Brava installations can use optional built-in thermostat controls. MarsLED stocks the Stelpro SIBT1W single-pole and SIBT2W double-pole thermostat options.
Shop Stelpro Brava heaters for Whitby projects.
Compare stocked wattages, voltages and thermostat options from MarsLED.